Your Hughesnet system control center not working and you’re wondering what to do? Look no further, because you’ve just come across the best solution!
By the end of this post, you will be familiar with the easiest ways to troubleshoot your Hughesnet system control center and solve the issue as soon as possible!
If you’re unable to access the Hughesnet control center, first hard reset your PC and make sure you’re writing down the correct router IP in the web browser. Next, troubleshoot the connection with the PC as well as the network. Lastly you can factory reset your router/modem to check if that will help.
Next, we’ll check where the issue could be coming from and then troubleshoot accordingly.
If the control center of your Hughesnet internet is not accessible, it is utterly possible that you’re doing something wrong.
It really depends on whether you’re writing down the correct router IP in your browser because otherwise, you won’t be redirected anywhere.
Here are ALL possibilities in a list at your disposal to review:
1. Network Issue
If there is an issue with your network or internet connection, the control center might become temporarily unavailable.
2. Wrong IP
Writing the wrong IP in your web browser won’t redirect you to the correct web page where the control panel is.
3. Application Issue
Potential fault with your PC/browser might prevent you from accessing the control panel of Hughesnet.
4. Wiring Problem
A fault with the cables will deny your access to the control panel of Hughesnet as well.
5. Wrong Credentials
Lastly, if you’re entering the wrong credentials in the login page of the Hughesnet control panel, you won’t be able to log-in.
Now that we have these general causes mentioned, let’s learn more about how to fix the issue with the upcoming solution guide.
Before proceeding with any of the troubleshooting solutions, have you tried rebooting your entire setup?
Sometimes all it takes is a good restart of your configuration and everything might start working as before.
If a restart does not work, then you can start applying the solutions in the order that they are listed:
We will begin off with a firm hard reset on your PC device. Unlike the normal reboot from the Windows start menu and power button, this method will power cycle your PC’s power supply way more appropriately.
That will restart ALL applications including your browser and network services which might help.
Follow these steps to hard reset your PC:
- Turn OFF your PC from the power button.
- Unplug the power adapter from both ends.
- Wait for ~5 minutes until your PC fully cools down.
- Flip the switch of your PC’s power supply and position the power adapter.
- Lastly, flip the switch of the power supply and run your PC.
Once you’re done with these steps, try accessing the control panel and see what happens.
It is possible that you’re using the wrong gateway to get into Hughesnet’s control panel.
To get your network’s default Gateway, follow the steps down below:
- Open the Command Prompt of your PC, by writing “CMD” in the Windows start menu.
- Open as Administrator.
- Click enter and in the CMD write “ipconfig”.
- Press enter and copy the IP next to “Default Gateway”.
- Paste it in your browser and try logging in to your Hughesnet.
If you’re wondering what the above-stated IPs mean, these are your modem/router’s IPs that will get you into the settings once inserted in your browser.
You need to have your PC wirelessly or wired hooked to your router.
One of these Hughesnet control panel IPs should definitely get you into the settings. If none of them work, then you should continue with the next solution.
If you’re certain that you’re using the correct IP to log into the Hughesnet control panel, then the next suspect would be the Ethernet connection with your PC.
In order to access the control panel in the first place, again you must have your router/modem connected to your computer or wirelessly.
Most users use Ethernet cable to connect their Hughesnet modem to their PC, so we suggest reconnecting that cable connection and making sure there isn’t any visual hardware damage.
Plug the cable tightly, even switch its sides and if you have a replacement cable do not hesitate to put it in use now!
It is a rare occasion, but if your network is severely overloaded you might not be able to reach anything.
We’ve designed complete steps to ensure that the problem is not coming from the network itself.
1. Disconnect unused devices – Any devices that you don’t actually use, don’t have to be connected to your router’s WiFi.
2. Reduce overall usage – Until the end of this post, make sure your network is not streaming in high quality and you’re not uploading/downloading large files.
3. Disable Windows Firewall – Go to the Control Panel > Windows Firewall > Disable ALL 3 shields.
4. Disable Antivirus – Some anti-virus software might block the connection to certain web pages so make sure to temporarily disable yours.
5. Take care of interference – Remove any devices that could conduct interference, such as large metal objects close to your router as well as RF transmitters.
Once you’re done with these steps, restart your PC and try logging in to the Hughesnet control panel again.
Tip: At this point, you should try using another web browser (Google Chrome or Microsoft Edge)
If your Hughesnet system control center is not workinga quick solution would be to flush your DNS.
This action will reset all network packets, which might be the reason why you’re unable to log in to HughesNet.
Here is how to flush your DNS in a couple of steps:
- Go to your PC’s desktop and open the CMD from the Windows start menu.
- Allow the CMD to make changes to your PC if you haven’t already and click on “Next”.
- Type “ipconfig /flushdns” and press the Enter button on your keyboard.
- Next, type “ipconfig /registerdns” and press the Enter button once again.
- Finally, type “netsh winsock reset”, hit enter, and close the CMD.
Once you’re done with these steps, restart your PC in order for the reset to take effect.
If flushing your DNS didn’t help, there is another workaround to bypass IP issues that might be preventing you from accessing Hughesnet.
Here is a quick explanation on how to renew your IP from Windows:
- Open the Windows start menu, type “CMD” and hit enter.
- In the CMD, type “ipconfig /release” and press the Enter button on your keyboard.
- Next, type “ipconfig /renew” and press the Enter button again.
- Finally, do “exit” and hit the enter for a final time.
After this action is done, make sure to restart your PC again, before trying to access Hughesnet.
Lastly, if nothing has worked so far and you’re still not able to get in the control panel, we suggest factory resetting your router.
This will reset all network settings and you will have to re-configure them once the reset is finished.
Follow these steps to factory reset your modem:
- Locate the factory reset button on the back of your modem.
- Make sure your modem is running before initiating the reset.
- Press the reset button and hold it down for ~30 seconds.
- Wait for the LEDs to start flashing after nearly 30 seconds of holding and release the button.
Your modem will now restart and afterward, you will be able to log in to Hughesnet using the getaway IP and the default credentials.
To fix the Hughesnet control panel, first hard reset your PC, modem, and router then make sure your writing is correct. Next double-check the router IP and troubleshoot the network. Lastly, you can factory reset your router.
Now that you know why Hughesnet system control center not working, you should be able to easily resolve the issue with our easy troubleshooting solutions.
In the end, you can always reach out to Hughesnet or your ISP for help reaching the control panel.
Finn Wheatley holds a Master’s Degree in Computer Science from UCL, London. He helped small data science consultancy firms, helping large corporations to grow their data capabilities, deploy advanced machine learning-based analytics and troubleshoot tech-related issues.