Wondering how to reprogram DIRECTV remote in easy steps? Search no further, because you have just found the most detailed and easy step-by-step tutorial to follow.
Here we’ll go over all details you need to know so you can confidently reprogram your remote without any trouble.
To reprogram your remote, you must perform a factory reset on the device, to disconnect it from the receiver. Once reset, you must use the “Fast Forward” and “Rewind” buttons to get it back connected.
Simplified, the process sounds like this.
However, there are many things you should be aware of so you can perform the process without any concerns so let’s jump right into it.
How To Reprogram My DIRECTV Remote Easily?
We assume that you have run into some troubles if you’re looking forward to reprogramming your remote.
The process is not complicated at all, but what makes the users struggle, is the pairing afterward.
Once you have reset your remote, it will lose connection with the receiver, which later might cause problems.
In that regard, we’ve prepared this step-by-step guide including everything and it should work flawlessly.
Step #1 Inspect The Remote
The very first step before the actual programming would be to discharge your remote so you can prevent any trouble during the process.
Down below we have prepared some steps to help you power cycle your remote easily:
- Unscrew the battery compartment of the remote or use the safety latch. (Ejecting the batteries might differ throughout the various types of DIRECTV remotes).
- Take out the batteries of your remote.
- Press and hold each button on the device for ~5 seconds.
- Hold the power button for an additional 10 seconds.
- Re-insert the batteries and install the compartment on top of them.
- Screw the compartment tightly.
If you’re eligible to change the batteries, we suggest doing that as well.
You never know at what time the batteries might decide to give up on your remote, so it is best to be prepared!
Step #2 Prepare Your Setup
Now that you have your remote inspected and ready to go, you must do the same thing with your receiver/TV.
If during the reprogramming your receiver isn’t functional, it won’t be able to detect your remote signal, therefore leaving your DIRECTV disconnected.
We advise you to simply make sure everything in your configuration is running, as well as the TV your receiver is connected to. Check for any loose cables, power adapter problems, etc.
If everything feels right, it’s time to reset the remote.
Step #3 Reset Your DIRECTV Remote
Once your remote and setup are ready, it’s now time to learn how to reprogram DIRECTV remote.
The reprogramming pretty much involves disconnecting the remote and then pairing it back once it has lost signal to the receiver.
This is why you must first execute a software reset on your remote, to make it lose signal with the receiver.
To perform a factory reset on your DIRECTV remote, follow the steps down below:
- Locate the “Dash (-), “Apps” or “Diamond” buttons, depending on your remote’s type.
- Press and hold the “Dash” button, as well as the “Apps” or “Diamond” button and wait.
- Release the buttons once you see that the LED on your remote has blinked in blue color twice.
- Quickly press and release the red button, which should be on the side of your remote (This will execute a restart).
This is how to disconnect your DIRECTV remote from your TV receiver or TV itself.
Keep in mind that your remote can be used both with the receiver and a TV, depending on your setup and configuration.
The process is pretty much the same but we’ve figured it would be helpful to mention. Now let’s get your remote paired.
Step #4 Pair Your Remote Back
To complete the reprogramming, you must reconnect your DIRECTV remote back to the device you have unpaired it from.
You don’t have to worry whether the device you’re pairing your remote to is a TV or receiver as long as you’re executing the process correctly.
To pair your DIRECTV remote back to the receiver/TV, follow the steps down below.
- Make sure you have removed the battery tag of your remote’s compartment.
- Turn on your TV and receiver.
- Point your remote towards the device.
- Locate the “Fast Forward” and “Rewind” buttons on the remote’s hardware.
- Hold both the rewind and fast-forward buttons for an average of 30 seconds.
- Wait for the confirmation message to appear on the output device and tap “OK”.
If the confirmation message disappeared after tapping the “OK” button on your DIRECTV remote, then this indicates that the programming was successful.
If pairing didn’t work, then go back to the beginning of this step and make sure you’re doing everything right.
Step #5 Set The Remote Options
Now that you know how to reprogram a DIRECTV remote, you will have to carry out the setup prompts.
You will have to choose the correct settings to make your remote the way you intend to.
Choosing WiFi
A screen that has discovered all of the networks should have appeared on your device.
Make sure to choose your own WiFi and insert the password key. Tap on the OK button and give your device a couple of minutes to set up the remote.
Selecting Appropriate Room
After connecting with the WiFi, you will be required to choose the room in your household where your DIRECTV remote and device are located.
This is usually meant for smart systems, so you may skip this step.
Sync Your Google Account
Finally, you will be prompted to sync your device with a Google account. Make sure to insert your credentials and confirm with an email sent to your inbox.
Once choosing OKAY, you will be sent to the main screen where you can start watching your favorite shows.
At this point, your remote should be successfully reprogrammed and working.
If there are any issues you’re experiencing, you might perform the process as many times as you need.
Quick Recap:
To reprogram the DIRECTV remote, first, perform a factory reset by holding the Dash button and the “Diamond” button. Then to program your DIRECTV back to the device, hold the “Rewind” and “Fast-Forward”. Lastly, carry out the setup to finalize the process.
Read Next: How To Fix DirecTV Go Error 1101?
Bottom Line:
Now that you know how to reprogram DIRECTV remote easily, you can perform the process whenever you’re experiencing issues.
The reprogramming refreshes ALL services and it really helps with glitches, bugs, or any other sort of issues that your setup might experience.
If the reprogramming process fails and you’re unable to complete it, you might need to contact the remote’s developers team, to help you out.
Finn Wheatley holds a Master’s Degree in Computer Science from UCL, London. He helped small data science consultancy firms, helping large corporations to grow their data capabilities, deploy advanced machine learning-based analytics and troubleshoot tech-related issues. Check out more about him here.