Spectrum Your TV Will Be Right With You? – (Quick Fix!)

When you want to watch your favorite show, and you see on your Spectrum your TV will be right with you, it can be pretty annoying. Fortunately, we have the solution!

Whenever this happens, your Spectrum service is going to be stuck until you can go beyond this message.

We recently found these steps that will get this issue fixed in no time.

Do you want to move past this message and enjoy your favorite Spectrum content?

Let’s get to it!

If you are stuck on “Your TV will be right with you,” restart your Spectrum box. Start by unplugging everything and leave them be for a while. Then, reconnect everything. If this doesn’t fix the error, update the software. Your device may be running an outdated version.

Now, there are many possible reasons you see this error message on your TV.

Before we proceed to the solutions, let us discuss in detail the causes.

Causes of Your TV Will Be Right with You L-3 Error

When your Spectrum box shows this error, it usually indicates a problem with your connection, hardware, or software.

The error means your cable box tried to access files from this location but failed.

Here’s why:

1. Connection Issues

Your power cord may not be properly connected to the receiver and power source.

Either the coax cable isn’t connected to the cable outlet on your wall, or the HDMI cable isn’t connected to the HDMI port on your TV. As a result, the receiver loses power.

2. Power Delivery and Failures

The wall outlet you are using to power your Spectrum box might be damaged. In this case, it needs to be replaced by your provider.

3. Faulty Remote

Either there is physical damage to the remote, or you’re having pairing issues.

You should also check your remote’s settings and study the different code combinations. 

4. Outdated Software

You may have forgotten to update your cable box. If something is wrong with your Spectrum device, this may cease your services and make the message appear.

Now that you know the possible causes of the Spectrum L-3 error let us proceed to the solutions.

How to Fix Spectrum Your TV Will Be Right With You

It may sound like a cliché, but a simple restart can fix just about anything. If you encounter an L-3 error: Spectrum your TV will be right with you. Try rebooting it.

If the cause isn’t serious, performing a quick restart with your Spectrum box can remedy the issue.

You’ll also want to reboot your TV just to make sure everything is working. Otherwise, try the following troubleshooting steps.

Solution #1: Discharge Your Spectrum Box by Unplugging It

If a restart does not do the job of resolving this issue with your Spectrum box, you can try performing a power cycle.

It’s a restart that also includes unplugging your box to discharge it fully.

It’s an effective way to clear out any bugs and glitches on your box’s software that can cause the “Your TV will be right with you” notification to come up.

Here’s how to power cycle your Spectrum cable box:

1. Turn off your Spectrum box.
2. Unplug it from the wall outlet.
3. Press and hold the Power button for 10 seconds to discharge.
4. Wait for an additional 2 to 5 minutes before plugging it back in.
5. Turn on your box to check if it continues to load.

Note: If you did this correctly, a countdown timer should appear with the notification, and the picture from your box should appear on your TV.

Solution #2: Tighten All the Connections on Your Spectrum Box

If there’s an issue with the signal coming from your Spectrum box, it can also show this notification on your screen.

The easiest way to deal with this is to make sure that all the cables and connections on your box are tight and secure.

This ensures that no loose cables or connectors can cause weak signals and the notification.

Here’s how to make sure your cables and connectors are tight:

1. Find the Cable In port on your Spectrum box.
2. Loosen the coaxial cable connector and remove it.
3. Make sure the connector is clean and free from dirt.
4. Insert the cable back into the Cable In port and tighten it.
5. Do the same for the HDMI port and cable on your Spectrum box.

Tip: You can also check the HDMI port and cable on your TV to avoid possible causes of a weak signal.

Solution #3: Replace the Batteries on Your Remote

When you see the “Your TV will be right with you” notification on your TV screen, it means that your Spectrum box is loading and searching for a signal.

If it’s stuck and taking more than 30 minutes, you need to press the OK key on your remote to know more about why it’s taking so long.

It will display more details, like a progress bar, so you know where you are exactly in the process.

If your remote is out of batteries, it will prevent you from getting the full picture. You want to replace it with a fresh set so you can monitor what’s happening.

Here’s how to replace the batteries on your remote:

1. Slide the door of the battery compartment.
2. Match the negative and positive ends of your terminals and battery.
3. Insert two AA batteries into the compartment.
4. Slide the door back to close it.
5. Turn on your TV and check if the notification appears.

Note: You will need to reboot your Spectrum box if it takes more than a couple of hours without the progress bar moving.

Solution #4: Plug Your Spectrum Box Directly into the Wall Outlet

Power delivery is also one of the possible causes of the “Your TV will be right with you” issue.

If your Spectrum box detects any issues with the power source or cable, it can manifest in a number of ways.

Sometimes the box can slow down and stop working altogether. You’re lucky if it shows this particular notification.

However, with this message, it’s not directly obvious that the issue comes from how you plug your box into the outlet.

Here’s how to properly plug in your Spectrum box:

1. Switch off your Spectrum box.
2. Plug it directly into the wall outlet.
3. To test, plug it into a known working outlet.
4. Make sure the power cable is plugged into your box securely.

Tip: Avoid using power strips or surge protectors with your Spectrum cable box.

Solution #5: Refresh Your Spectrum Receiver Online

A signal refresh may sound like a restart, but it’s more than that.

If you’re having issues with your Spectrum cable box, refreshing it is one tool in your troubleshooting arsenal that comes in handy in a lot of situations.

Refreshing the signal on your box resets its connection with the server.

It allows your box to reconnect with Spectrum’s service fixing errors like the “Your TV will be right with you” notification.

Here’s how to refresh your Spectrum box online:

1. Log in to your Spectrum account on the website.
2. Under the Your Service tab, select TV.
3. Select your box from the list.
4. Click on Restart Equipment.
5. Choose Restart Equipment again to confirm.

Note: This will restart your cable box remote and refresh its connection with the Spectrum servers restoring your service.

Solution #6: Refresh Your Box Using the Spectrum App

There’s also another way to refresh your box. Apart from logging into your account on the Spectrum website, you can also do it with the Spectrum app.

It’s a more convenient way to refresh your box, especially if you don’t have access to a computer.

As long as you have your phone, WiFi, and the Spectrum app, you should be able to fix your box and get it to sync with the servers.

Here’s how to refresh your Spectrum box using the app:

1. Sign in to the Spectrum app on your phone.
2. Go to Services.
3. Navigate to the TV section.
4. Choose the cable box you want to refresh.
5. Tap on Restart Equipment.

These are the proven ways how to resolve this error as quickly as possible.

If none of these steps work, you can reset your Spectrum box by pressing and holding the Reset button.

You can also contact Spectrum customer support to get additional help or ask them to refresh your cable box.

Bottom Line

If you continue to suffer from the Spectrum your TV will be right with you issues, these are the different methods you can try out.

The steps are easy and are proven solutions that will take care of this problem in no time so you can continue to have a great viewing experience with your Spectrum box.

Read Next: How to Fix Spectrum Error Code IA02?