Manhattan Freesat Remote Control Not Working? – Fix Guide

Your Manhattan Freesat Remote Control not working and you don’t know what to try?

We’ve got you covered on this one!

Whenever a remote goes faulty, most users just replace the batteries and attempt to use it again.

However, there is more to this problem than just the batteries and in this guide, we’ll review all of the possible occurrences with the remote and how to fix them!

Let’s go:

To fix when a Manhattan Freesat Remote Control isn’t working, discharge the device and settle wireless interference in your setup. Next, replace the unit’s batteries and power reset your TV box or receiving device. Finally, Factory Reset the remote.

To understand things in more depth, let’s figure out why this problem occurred!

Why Is Manhattan Remote Control Not Working On Freesat?

The Manhattan Freesat Remote Control is a device that could pair to any smart device and function as a universal unit.

However, particular occurrences with the remote itself or the receiving device, could interrupt that connection and prevent the remote from working.

Let’s review why your Manhattan Remote Control stops working:

• The Batteries Have Run Out that are inside your remote
• There’s Interference in your setup
• The Remote Got Unprogrammed from the receiver
• There’s a Hardware Malfunction with the remote

Although most users could think of only a thing or two to try when their remote stops working, we’ve got a full guide for you!

Keep reading to learn the best fix solutions out there!

Manhattan Freesat Remote Control Not Working – Fixed!

After learning what could potentially go wrong with your Manhattan Freesat Remote, it’s time we give a start to our troubleshooting!

We will go over the best-recommended solutions by the Manhattan community, reported as the most efficient and easy to try.

All you have to do is follow the chronological order of our guide and pay attention to all notes, tips and alerts we’ve included.

Let’s jump in!

Solution #1 Discharge the Manhattan Remote

Performing a Discharge on your Manhattan Remote could get things going again.

One of the reasons that the device has suddenly stopped working, is that it no longer receives charge from the batteries.

By reseating the batteries during the discharge, you’ll cause the remote to keep withdrawing electricity from then and therefore start working.

Here’s how to discharge your Manhattan Remote easily:

1. Place the remote with its buttons facing down.
2. Locate the Battery Compartment.
3. Take off the Battery Compartment Cover.
4. Eject all batteries inside the remote.
5. Press each Button on your remote for 5 Seconds (the power one for 30).
6. Re-install the batteries back into your remote as you mind the polarity.
7. Place the battery compartment cover.
8. Attempt to use your remote.

If the batteries were seated correctly into the remote, the LED of the device should blink after pressing a button. This is an indicator that the device now withdraws power.

Alert: If you’ve positioned the batteries incorrectly, your remote will not receive power.

Solution #2 Eliminate Signal Interference

Your remote’s functionality could have been interrupted by an Existing Interference in your setup.

Interference could be both wireless and physical based on what causes it.

For instance, wireless interference is caused by other devices that could suck in the signal of the remote or interfere with its own. As for physical interference, solid objects could cause it.

Let’s review the causes of the two types of interference and settle it!

Wireless Signal Interference:

Caused by:

• Bluetooth Devices near your cable box, TV, receiver or remote
• Baby Phones and RF or Radio Transmitters
• Cordless Phones or Other Signal Receivers

How to Fix: Move all mentioned devices away from your setup!

Physical Signal Interference:

Caused by:

• Furniture between your remote and receiver
• Missing Leverage of the receiver according to the remote
• Objects placed on top of the receiver

How to Fix: Make sure nothing is standing between your remote and receiver!

Side Note: Wireless interference could also impact Wi-Fi or Cellular functionality/

Solution #3 Power Cycle your TV Box/Device

The next thing you should do is perform a Power Cycle on the device at the receiving end.

So far we’ve only focused on your remote, but it would only be appropriate to seek out problems with the receiving device.

The best way to troubleshoot any issues with your receiver device, regardless of whether it is a box or a TV, is to power cycle it.

Learn how to perform a power cycle in these instructions:

1. Shut off your device by pressing the Panel Power Button.
2. Wait for the device to shut down.
3. Disconnect the Power Adapter of the device out of the wall outlet.
4. Wait for 5 Minutes while the device’s adapter is still unplugged.
5. Reattach the power cable to the wall outlet.
6. Turn on your receiver device and wait for it to start.
7. Attempt to use your remote on the receiver.

The longer you’ve kept waiting while the device was unplugged, the better it will power cycle and refresh its services.

Note: Plugging the device before 5 minutes have elapsed, will prevent the power cycle.

Solution #4 Replace Remote Batteries

Even if you’ve already replaced the remote’s batteries, you should do it again just in case.

• The Manhattan Freesat Remote uses 2 AAA Batteries for its compartment

There is a high chance that one or two of the batteries are not connecting properly or have no electricity remaining.

Either way, you should replace these batteries with brand-new ones and then attempt to use your Manhattan Freesat remote with the receiver device.

Here’s how to replace your remote’s batteries:

1. Grab a fresh pack of 2 AAA Batteries (they must be new)/
2. Place the remote upside down.
3. Remove the Battery Compartment.
4. Eject all of the batteries that are already inside.
5. Place the first AAA battery and then the second one.
6. Close the battery compartment.
7. Attempt to use the remote.

Once again, you must be aware of how the batteries are positioned inside the compartment. If they are inserted incorrectly, the remote will not receive power.

Note: Do not use second-hand AAA batteries since this could reduce the voltage.

Solution #5 Reprogram the Remote

There are high chance that the remote got unpaired from the receiving device and could not control it.

What you should do next, is perform the Reprogramming Process for your Manhattan Freesat Remote in order to get it connected with the receiver.

• Reprogramming causes the remote to connect with a receiver

Let’s learn how to reprogram your Manhattan Remote Control back to the receiver:

1. Grab the remote.
2. Turn on your Receiving Device.
3. Point your remote at the device.
4. Press and hold the Chosen Button on the TV remote.
5. Keep holding the Chosen button for 30 seconds.
6. Wait for the Remote to Blink and it should turn Rapidly Flash in Green.
7. Test the remote.

If the programming was successful, the LED of the remote will rapidly flash in green. Otherwise, you’ll not see any LED output from your remote.

Alert: If the programming failed, re-do all of the instructions above a second time.

Solution #6 Reset the Manhattan Remote

If nothing worked so far, then you should Reset your Manhattan Remote.

This is a standard solution for any issues with the device that envelops problems with both the software and hardware of the device.

A reset is recommended on the device if it is experiencing connection issues, temporal outages or issues withdrawing power.

Here’s how to perform a Reset on your Manhattan Freesat Remote:

1. Press and hold the Red Button on your remote.
2. While holding the Red button, press the AD Button.
3. Keep holding these two buttons for 5 Seconds.
4. Locate and press the Home Button on your remote.
5. Finally, hit the Red Button Again for 5 Seconds.
6. Wait for your remote to reset.

The LED of the remote will blink five times to indicate that the reset was successful.

The reset means that the remote control has deleted the existing TV code and has reset to a default-pairing setting.

Note: You may have to reprogram your remote after performing a reset on the device.

Quick Recap:

Hence, the solution when Manhattan Remote Control isn’t working is to discharge the device and replace its batteries. What you should do next is reprogram the remote and power cycle your TV Box or TV. Finally, reset the Manhattan Freesat remote.

Wrapping Up:

In this guide, we’ve learned why the Manhattan Freesat Remote Control not working and what are the main suspects for the trouble.

Although our solutions were designed to troubleshoot your remote from top to bottom, it could be that it reached the end of its life.

Read Next: How To Fix BBC iPlayer On Freesat Not Working?