Are you wondering why is Linksys Velop blinking red? Well, a Linksys Velop Mesh system is one of the best choices to get seamless Wi-Fi coverage for your home.
However, a red LED light on your Velop nodes indicates that something might be wrong with its connections, so let’s learn!
Many factors can cause the red light on the Linksys Velop, including loose wire connections and broadband faults. To fix this, you need to inspect the power source, check the wirin and perform a full reset.
Let’s move further to unwrap everything in more detail!
How to Fix When Linksys Velop Blinking Red?
If your Linksys Velop setup is intact but blinking a red light instead of a solid blue light, there’s something wrong with it.
The good news is that there are several ways to fix this issue and get your Velop system up and running smoothly again.
So, let’s get in!
1. Check the Power Source!
When your Linksys Velop router is blinking a red light, the first thing you need to look at is its power source.
This is crucial because Linksys Velop requires a constant power supply, and if your router receives insufficient or disrupted power voltage, it can lead to a red blinking light.
The reasons can be the following:
Here is how you can check the Velop power source:
- Unplug your Velop adapter from the outlet.
- Disconnect the power cord from the Velop.
- Then, inspect both ends of the power cable.
- Blow out the power cable port connector.
- Connect the power cord back into the Velop.
- Plug the power adapter into the wall outlet.
- If your outlet has a switch, ensure it’s “ON.”
In case you find any damage to the Velop power cable, replace it with a new one.
In addition, you can also try plugging your Velop into a different outlet to check if the red light goes away.
Tip: Verify that your Linksys Velop is not overheating!
2. Inspect the Cable Connections
If your internet connection is not working and the Velop is blinking red light, it could be due to a loose cable connection between the primary node and modem.
Another possibility can be that you have connected the Ethernet cable to the incorrect port or your Ethernet cable is faulty.
Therefore, start by checking whether the Ethernet and all other cables are securely connected to the Velop node, modem, or other nodes in the system.
Alternatively, disconnect all cable connections and reconnect them back into the correct ports on the devices just to double-check and ensure that everything is correctly set up.
Tip: You can also check your Linksys user manual to see where all the cables connect!
Damaged Equipment?
If all cables are correctly plugged in, but the red light persists, look for any signs of damage, kinks, wrapping, and cuts.
In addition, if you have an extra Ethernet cable available, try using it to check if the red light disappears.
If you’ve checked everything but the red light is still blinking, continue reading!
3. Restart the Linksys Velop Mesh!
Sometimes, the problem with Velop red blinking is simply a software glitch that may restrict the modem from establishing the internet connection with your Velop node.
Thus, the solution would be to restart your Velop system using the Linksys mobile app.
Info: The Linksys app is available for Android and iOS mobile devices!
Follow the steps below to restart your Linksys Velop setup:
- Enter the Linksys app.
- Sign to the Linksys app.
- Press on the “Settings.”
- Go to “Network Admin.”
- Press on “Restart Velop.”
- Choose the “Restart” tile.
This will restart your Linksys system by disconnecting all devices and then reconnecting them back again as soon as the connection is established.
Then, hopefully, you no longer see the red blinking light, and if you do, then there are many more solutions to attempt, so continue reading!
Tip: Feel free to reboot your system every time you experience errors!
4. Move Velop and Modem Closer
If your Linksys Velop blinking red light, it may be due to the distance between your modem and the Velop.
Hence, even if your devices are not set up too far apart, signal interference or weak Wi-Fi signals can cause signal loss between your units.
The solution is simple!
Look for a central location within your home and move all the primary and other nodes closer to the modem.
Sometimes, even if your Velop node is placed next to the modem, it will still blink a red light due to nearby electronic devices.
Here’s a list of some potential factors of signal interference:
- Cordless phones and RF headphones.
- Microwave ovens and Bluetooth units.
- Wireless video cameras and monitors.
- Fluorescent lighting and metal objects.
So, position the WiFi devices strategically to minimize the chances of signal loss or interference.
If no electronics are interfering with the connection, but the red light is still there, you may need to attempt even further troubleshooting, so keep reading!
5. Update the Linksys Mobile App!
Sometimes, using an outdated app version causes issues and affects the connection between your Velop and other nodes.
In that case, updating your Linksys app may help resolve the Velop red blinking light issues, as the latest updates often involve bug fixes and OS improvements.
Here is how you can update the Linksys mobile app:
- Grab your Android or iOS phone.
- Go to the Play Store/App Store.
- Then, search for the “Linksys” app.
- Tap on the “Update” (if available).
- Wait for the update to complete.
After that, power cycle your entire Linksys setup, including all parent and child nodes.
Wait up to 5 minutes until the device boots up completely and establishes the connection, and then test…
Tip: Always keep your Linksys app up to date!
6. Update the Linksys Velop Firmware!
Often, when the Linksys Velop red light blinking, the firmware of the device turns out outdated!
When the modems are not updated regularly, it may often develop software issues.
Many users make the mistake of ignoring software updates, which can lead to connectivity issues.
So, if you haven’t updated your Linksys firmware, don’t worry because it’s not too late, so let’s learn how!
Follow these steps to update the Linksys firmware:
Step #1 Download the Firmware
- Open a web browser on your device.
- Navigate to the Linksys Support web.
- Provide your Linksys Model Number.
- Then, click the “Get Support” button.
- Next, click on “Download/Firmware.”
- Then, choose your hardware version.
- Download and Save the firmware file.
Step #2 Perform the Update
- Open the web browser on your device.
- Go to the Linksys Velop’s user interface.
- Locate the “Network Administration.”
- Tap on the “Firmware Upgrade” button.
- Then, click on “Browse”/“Choose File.”
- Find the downloaded file and click “Open.”
- Click on “Start Upgrade” or “Upgrade.”
Once the firmware upgrade process ends, reboot your Linksys router and wait for the devices to establish the connection.
After that, check if your Linksys red light blinking problem is there…
Note: Avoid pressing any buttons during the upgrade process!
7. Factory Reset the Linksys Velop!
If you’ve tried every step in the guide and the red light is still blinking on your Velop, perform a factory reset as a last resort.
This reset will permanently erase all configurations, and you’ll need to reconfigure your Velop system from scratch.
Tip: Implement this step on the weekdays so you can contact your ISP in case of problems!
Follow these steps to factory reset the Linksys Velop router easily:
- First, locate the “Reset button” on your Velop.
- Then, press and hold down the Reset button.
- Keep holding until the node turns red and fades.
- When the red light flashes, release the button.
Your Linksys Velop router is finally restored to factory default settings.
When ready, you must re-configure your Velop to enjoy the seamless experience of your Linksys Velop WiFi coverage.
Note: If the red blinking light problem persists, contact Linksys Support!
Quick Recap:
If your Linksys Velop blinking red, restart the Velop and inspect whether the power cable and adapter are intact.
In case the issue continues, move the devices closer, update your Linksys app and Velop’s firmware, or perform a factory restoration to solve the problem!
Follow us for more!
Finn Wheatley holds a Master’s Degree in Computer Science from UCL, London. He helped small data science consultancy firms, helping large corporations to grow their data capabilities, deploy advanced machine learning-based analytics and troubleshoot tech-related issues. Check out more about him here.