How to Reset Setek WiFi Extender? – Easy Steps

Wondering how to reset Setek WiFi extender? The process is not that simple…

You’ll need to trigger the reset from the Setek Extender and then reach into the router’s Control Panel to finish the process.

In case you’ve never done something like this before, make sure to have a Windows computer + internet at your disposal to reset the Setek extender in no time!

The Factory Reset on Setek Extender happens through the network device (router/modem) control panel after the reset button has been pressed. Reaching the control panel happens by logging in using the default Admin credentials.

Let’s next learn whether a complete reset on the Setek extender is possible or not!

Can a Setek WiFi Extender Be Reset?

In general, a factory reset on your Setek WiFi extender is often performed whenever the device refuses to work properly.

A reset is at hand, whenever the extender starts causing plenty of network dead zones in your household and the reset could work flawlessly to resolve these problems.

The Setek WiFi extender can be reset!

What the reset actually does is refresh the software of the device. It will restart all services of the extender and resolve any network-related problems with the device.

Will the reset do any harm to your device? Absolutely no!

Note: The reset is a top solution whenever the device has WiFi or network-related problems.

Now, let’s learn what is the way to perform a reset on your WiFi extender:

How to Factory Reset Setek WiFi Extender?

To perform a factory reset on your Setek WiFi extender we’re going to use the help of the steps below.

We made sure to include every possible outcome and potential issue so you can freely perform the reset process without any obstacles.

Let’s jump right in!

Step #1 Plug Your Router & Extender

Before we get to the essential reset process, there are a couple of preparation steps you should undertake.

The first step, as the name suggests, is to plug in your router and the WiFi extender you wish to perform a factory reset on.

Both of the devices must be plugged into an Electrical Socket.

It’s suggested that both your router and extenders are into separate sockets and you avoid the use of an electrical splitter.

Two wall outlets should do well for the reset process, since stable power is required for this operation, especially for your Setek WiFi extender.

Note: Both devices’ LED lamps must be lit up as soon as you plug them into the power!

Step #2 Place Router Near the Extender

One last preparation factor is to take the router near the WiFi extender and wait for the Setek device to connect with the router. Only then you shall proceed with the factory reset process.

Simply put the router 5-10 Meters away from the WiFi extender and wait for the LED on the Setek unit to turn into a green color.

The green color means that the extender got successfully connected with the router and you could now perform the factory reset process.

Note: The router will also identify the connection once the extender pairs up with the device.

Step #3 Locate the Reset Button

The rest of your Setek WiFi extender consists of both pressing the physical Reset button and triggering the reset through the router’s settings.

Of course, your first task is to press the physical reset button to trigger the reset sequence on the extender.

• There is a Reset button on the bottom panel of your Setek WiFi extender!

Give the device a couple of brief looks and you should be able to locate the button, which you will have to use.

This button does not completely reset your extender but puts it in a state in which you could trigger a software reset.

Once you’ve found the button, proceed with the next step to start the essential reset!

Tip: If you struggle to locate the Reset button, unplug the device and locate the button!

Step #4 Press the Reset Button

Your next step is to press the Reset button on your Setek WiFi extender.

The button must be pressed for a certain amount of time and the LED should go into a specific color to indicate the reset state of the extender. Let’s learn how!

Follow these instructions to successfully trigger the reset state of your Setek extender:

1. Press and hold the Reset Button on your extender.
2. Keep holding the button for 10 Seconds.
3. Let go of the button after that time.
4. Wait for the LED on your WiFi extender to turn into Red Color.
5. Wait for another 30 Seconds while your Setek extender’s LED is in red.

Note: The extender’s LED light will go off at some point, but that doesn’t mean that the reset has failed.

Step #5 Get Router’s Default Gateway

The next step is to acquire the router’s Default Gateway IP.

If the extender is connected to the router, its factory reset option will be accessible through the router’s settings.

However, in order to access those options and configurations, you will need the aforementioned address!

Here’s how to acquire your network’s default gateway in easy steps:

1. Get a computer or a laptop that is connected to the router’s WiFi.
2. Open the Windows Menu.
3. Type “CMD” and press the Enter Button.
4. Wait for the Command Prompt to open.
5. Once the window has appeared, type “ipconfig” and press Enter.
6. Scroll down and search for “Default Network Gateway”.
7. Copy the IP address next to the default gateway label.
8. Exit the Command Prompt.

Keep reading to learn how to access your router’s settings!

Note: Within the CMD, copy the default gateway after highlighting it and pressing Enter.

Step #6 Access Router Settings

Now that you have the Default Gateway Address the next step is to access the router’s settings.

Within the router’s Control Panel, you will find a configuration of your Setek extender and from there, you could trigger a complete factory reset.

Here’s how to access your router’s settings in easy steps:

1. Open the Browser on your desktop computer or a laptop.
2. Paste the Default Gateway into the search field of the browser.
3. Hit the Enter Button.
4. Wait to be redirected to your router’s login screen.
5. Once there, use “admin” for both username and password.
6. Press the “Sign In” button to get into your router’s settings.

Note: If “admin” doesn’t work for the password field, test with “password”.

Step #7 Go to the “Management Tab”

The last thing you have to do before being able to factory reset your Setek extender is to head to the management tab in your router’s settings.

There, you will have access to the Setek device’s configuration and therefore be able to reset the device.

To enter the management tab, all you have to do is press the “MANAGEMENT” button, located on the right side of your computer screen, within the router settings.

Once there you should be able to start the factory reset on your Setek WiFi extender in the final step!

Note: With different router settings, the Management tab could be “Accessibility settings”.

Step #8 Factory Reset the Extender

Once in the Management tab, the Setek WiFi extender will detect the pressing of the physical reset button and prompt you whether you want to reset the device or not.

On this prompt, you will have to press the “Confirm” button to proceed with the factory reset.

If there are any additional steps to this reset after confirming the prompt, follow them to finish the process. You will be let know whenever the extender is reset and ready to go!

Alert: Do not exit the router settings while the reset is still ongoing since this could cancel the process halfway.

Quick Recap:

Hence, to reset a Setek WiFi Extender you’ll need to press the Reset button on the device’s panel and reach into the router/modem control panel to finalize the process. You can reach the network device control panel by using the Default Gateway IP address.

Read Next: WiFi Router Not Working After Reset? – Fixed!

Wrapping Up:

Here we’ve learned everything about how to reset Setek WiFi extender in a few easy-to-follow steps that cover absolutely everything.

We hope that this post was helpful and that you’ve managed to successfully reset the Setek WiFi Extender. Good Luck!

For more relevant “how-to” guides such as this one, make sure to check our blog!