To understand why SONIQ TV won’t turn on red light, continue reading this quick guide!
A malfunctioning SONIQ TV with a red-coloured standby light can often be a remote-related issue or power insufficiency.
Thus, by the end of the guide, you’ll perfectly know all possible causes for the fault of your SONIQ TV and what can be done to resolve the red light problem,
If the SONIQ TV isn’t turning on and shows a red light, power reset the TV, troubleshoot the remote control, and check for IR obstructions. If the issue persists, plug the SONIQ TV into a different outlet and replace the TV’s power adapter.
Let’s learn more!
My SONIQ TV Won’t Turn On But the Red Light Is On?
The SONIQ Standby light displays the current power state of the SONIQ TV and whether you have turned on the device.
The active Standby light is typically a good sign since there hasn’t been a problem with the power supply of the TV.
If the lamp powers off, there could be trouble.
Here’s a list containing all causes for the red light on your SONIQ TV:
What Does the SONIQ “Standby” Light Mean?
Like all TVs, the “Standby” light only comes on when powered off.
Upon turning on the TV by pressing either of the power buttons, the Standby light goes off until the television powers off.
You can typically tell if the TV is receiving a proper power supply by the status of the “Standby” light.
The light only has two states – “On” and “Off” and only comes on in red colour.
Remember that the “Standby” light on SONIQ and most TVs do not blink and only stay solid red, always.
Alert: If the “Standby” does not come on, there could be a power supply failure!
SONIQ TV Won’t Turn On Red Light – Fixed in Minutes
Note: If there’s an input-related black screen on your SONIQ TV remote, attempt to alter the input by pressing the “Source” button on the remote control.
1. Long-press the Power Button
In case of a remote failure or issues with the TV’s hardware, you can Soft Reset the SONIQ TV by continuously holding the physical Power button on the back.
For this purpose, the SONIQ TV must remain connected to an electrical outlet, and you must not release the button prematurely.
Here’s how to long-press your SONIQ TV’s power button properly:
- Verify that the SONIQ TV is connected to a power supply.
- Locate the Power button on the lower left or right TV end.
- Hold the button for ~15 seconds without releasing it early.
You can only release the power button early if the SONIQ TV’s display flashes up or turns on and a picture is displayed.
Before you see any output from your SONIQ TV, do not release the physical power of your SONIQ TV, or the soft reset will fail.
The goal is to discharge your TV.
2. Power Reset the SONIQ TV
One of the reasons why the SONIQ TV is refusing to turn on could be due to a failure of the power supply.
You can quickly address issues with the TV’s electricity income by temporarily unplugging the power adapter of the SONIQ from the power outlet and connecting it back in.
Here’s how to undergo a power reset procedure on your SONIQ remote:
- Disconnect the power cord from the back of the SONIQ TV.
- Unplug the other end of the cable from the electrical outlet.
- Next, wait for 30–45 seconds while SONIQ is disconnected.
- Reconnect SONIQ’s power cable into the electrical outlet.
- Connect the other end of the adapter to your TV power port.
Your SONIQ TV should feel cold to the touch after it has adequately discharged.
Attempt not to touch the display of the TV, instead, lay your hand on the rear panel to test the temperature.
Notice: Do not reconnect the TV before at least 60 seconds have elapsed upon unplugging!
3. Uninstall SONIQ’s Surge Protector
The power strip, more widely known as “Surge Protector,” can partially reduce or suspend the power supply of your SONIQ TV until further notice.
In case of a potential defect with your surge protector, the “Standby” light may remain red, but you cannot turn on the TV.
How to Test SONIQ TV Without Surge Protector?
To determine if the fault of your SONIQ TV comes from the surge protector, you should connect the TV’s power cable directly to a power outlet.
This will verify that the A/C of the TV is stable and that malfunctioning strips or third-party devices cause no interruptions on your SONIQ TV.
Alert: Remove all third-party equipment from your SONIQ TV while testing!
4. Troubleshoot the Remote Control
Even if your SONIQ’s Standby status lamp is active, a malfunctioning remote control will prevent you from turning on the TV.
That’s why the next step will guide you through standard remote troubleshooting to resolve communication issues with the SONIQ TV.
Attempt the following solutions on your SONIQ TV remote control:
- Discharge the remote control by reinserting the batteries.
- Improve the line of sight between the remote and your TV.
- Insert a fresh set of batteries in the SONIQ remote control.
- Clean the remote’s battery compartment and the TV “eye.”
Standard IR and Bluetooth SONIQ remotes typically use two triple-A batteries, but older models may use two double-A batteries.
By accessing the compartment and removing the batteries, you can determine the battery type since it’s important to use the correct ones.
Tip: It is advised to replace the SONIQ remote’s batteries every 2–3 months!
5. Plug Your TV to a Different Outlet
Even if the TV’s Standby status lamp is on, the issue can be caused by potential power insufficiency due to a defective power outlet.
You can test the TV’s equipment and hardware by installing the unit’s power cable into an alternative power outlet with proven functionality.
So, relocate the necessary equipment next to another proven outlet and plug the SONIQ TV with the new electrical outlet.
Wait for 10 seconds, and check if the “Standby” light comes on.
Tip: You can test any electrical outlet in your home by connecting any low-voltage device!
6. Ensure SONIQ TV is Not Overheating
SONIQ TV red light won’t turn on can be a potential aftermath of unexpected hardware overheating due to overutilisation.
Your SONIQ TV must avoid overheating at all costs to preserve the hardware and maintain the proper functionality of the CPU and motherboard.
How to Tell if SONIQ TV is Overheating?
If the TV powers off all of a sudden, feels hot to the touch more than regular or displays a blank image, you can easily tell it is overheating.
Upon reaching the internal thermal margin, the TV will power off, and you will be unable to start the TV again until the hardware cools off.
Why is SONIQ TV Overheating?
Here are the possible causes why SONIQ is overheating:
- Dusty air ventilation openings.
- Issues with the power setup.
- Internal hardware malfunction
- Nearby heat conductor units.
How to Prevent SONIQ TV Overheating?
Here’s how to prevent your SONIQ TV from overheating:
- Dislocate any heat conductors from near the SONIQ TV.
- Unplug the TV power cable and wait for about 5 minutes.
- Prevent direct sunlight from shining on the SONIQ panel.
- Unplug the TV and remove all dust from the vent openings.
Alert: Prolonged overheating can seriously damage the SONIQ TV’s hardware!
7. Replace the SONIQ TV’s Adapter
If all solutions this far into the guide fail, you should consider replacing the power adapter of the SONIQ TV with a brand-new one.
If the cable can no longer transfer power from the outlet to your TV adequately, you cannot turn on the TV due to insufficient electrical flow.
Most SONIQ TVs use a standard-connect 12V TV RF cable, and you can explore different power cable options for your TV at many online stores.
Whenever the SONIQ TV won’t turn on red light, power cycle the TV and troubleshoot the remote control.
Also, verify the SONIQ TV is not overheating, disconnect the wall socket connectors and plug the TV to a proven power source.
Follow us for more!