Fetch TV troubleshooting no signal is an easy task as long as you have the correct steps!
Troubleshooting the “No Signal” error on your Fetch TV cable box includes the channel lineup, the TV connection and configuring the box’s settings.
So, this guide will provide you with the best methods and solutions for restoring the reception of your Fetch TV in a matter of minutes.
To troubleshoot “No Signal” on the Fetch box, correct the input source on the TV, inspect the antenna cable and re-tune for available OVA/FTA channels. Additionally, test your box on a different TV and conduct a factory reset.
Let’s learn more!
Fetch TV No Signal – Causes & Reasons
The “No Signal” message on your Fetch box could be caused by bad weather, antenna issues or equipment malfunction.
So, the first step to understanding what could degrade the signal of the Fetch TV cable box is reviewing all potential causes.
Here’s a short and organised list containing all causes for no signal:
This could degrade the signal of the Fetch TV box and cause loss of broadcasts or usable TV signal.
So, to fix this, proceed further into the guide to explore possible solutions!
Fetch TV Troubleshooting No Signal – Here’s How to Fix
You can restore your Fetch TV signal in a couple of easy steps listed below:
1. Check the TV Input Source
If the TV keeps displaying a “No Signal” error, you might have selected an improper input through the TV’s Source Menu.
The Fetch TV box must be connected to one of the available HDMI ports on your TV, and you must select the corresponding input in the TV source menu.
Here’s how to adjust the source on most TV devices:
- Press the “Input” button on your TV’s remote control.
- Check which TV HDMI port the box is plugged into.
- Highlight the corresponding input in the source tab.
- Press the “OK” button on your TV’s remote to select.
- Wait until the source displays the Fetch box’s output.
Bonus Tip: Test on a Different Input
If the TV or monitor fails to display the TV’s broadcast, plug the HDMI cable of the streaming unit into an alternative port on your TV.
After that, set the new input as default within the TV’s source menu and wait until the output of your Fetch TV box appears on the television screen.
Reminder: Have you tested on all available TV HDMI inputs?
2. Hard Reset the Fetch TV Box
The “hard reset” may sound frightening solution at first, but it’s a simple power cycle that only discharges the residual electricity from your device.
This not only reboots the operating system but also solves issues with the hardware that may be affecting the signal of your Fetch TV box.
Here’s how to perform a hard reset on the cable box:
- Unplug the power adapter from the back of the box.
- Disconnect the other end of the cable from the A/C.
- Wait for 60 seconds while the cable box discharges.
- Reconnect the supplying cable back into the outlet.
- Plug the other end of the cable into your Fetch box.
While the Fetch TV cable box is unplugged, we recommend inspecting the physical condition of the power equipment and removing any dust or obstruction from the power port.
This may reset the signal and solve your problem instantly.
Important Note: Verify that the power cable of the TV box is securely installed on both ends!
3. Reconnect the Antenna Cable
You can quickly refresh the reception and signal detectability of the Fetch TV box by re-seating the antenna cable.
The antenna jack provides the Fetch TV box with reception and access to FTA channels for your area via wirelessly signal detection and decoding.
Here’s how to reconnect the antenna cable of the Fetch TV box in easy steps:
- Unplug the antenna cable from the “Antenna In” jack.
- Verify there is no dust accumulation/debris in the port.
- Wait for 60 seconds while the antenna cable is unplugged.
- Reconnect the cable back into the antenna jack on the box.
While the antenna cable is unplugged, inspect the antenna ports and the physical condition of the cable for defects or damages.
A malfunctioning antenna cable could degrade the signal’s quality or cause a complete signal loss of the FTA or OVA channels on the Fetch cable box.
Reminder: Verify that you’ve connected the antenna cable to the TV box securely!
4. Re-Tune for Fetch TV Channels
A temporal loss of channel data can be caused by Fetch TV no signal, leading to issues with the tuned OVA or FTA channels.
All you need to do is access the programming configuration of the cable box through the settings and start tuning.
Here’s how to re-tune for channels on your Fetch TV cable box:
- Open the Fetch menu using the box’s remote control.
- Select the Gear indicator and then choose “Channels.”
- Select “Channels” and press on “Full Channel Scan.”
- Enter the default cable box PIN (0000) when prompted.
- Wait until the Fetch TV box completes a channel check.
The turning option of the Fetch box will only add channels already available for your antenna’s location.
Some broadcasts may appear degraded or be lost entirely if the transmission signal is improper due to lousy weather, significant travel time or location.
Note: The tuned channels will be automatically assigned to the Fetch TV guide!
5. Inspect the HDMI Connection
The “No Signal” message could be a result of an inappropriate connection between the TV or viewing device and the Fetch TV cable box.
The next step is to inspect the HDMI connection between the devices and attempt to validate issues with the connection and the signal transfer.
Here’s how to effectively resolve signal issues with your Fetch box’s TV device:
- Perform a “power cycle” on the TV connected to the Fetch box.
- Plug the HDMI wire of the Fetch box into an alternative TV input.
- Replace the HDMI cable used for transferring the box’s output.
Bonus Tip: Test on a Different TV/Monitor
If you’re still unsure whether the TV or your monitor causes the “No Signal” message, testing the Fetch box on an alternative monitor is strongly recommended.
Hence, relocate the current viewing device and position an alternative TV or monitor compatible with HDMI cables to test.
Tip: If you have a replacement HDMI to test with, implement the cable during this step!
6. Check for Antenna Obstructions
You can improve the signal deciphered by the Fetch TV box by correcting issues with your outdoor/indoor antenna’s positioning, elevation or surrounding conditions.
There are multiple steps to undertake that will significantly improve the received reception of the box.
The following can degrade the acquired signal by your Fetch TV box’s antenna:
- Precipitation of the Fetch TV box antenna’s surface.
- Extreme weather conditions/obstructive sky clouds.
- An ongoing blizzard or a heavy aerial thunderstorm.
- Issues with the elevation or the antenna’s azimuth.
Typically, there are no set requirements towards the positioning of the antenna to receive the best reception possible, but it is strongly advised to elevate as high in the air as possible.
The more elevated your Fetch TV box’s antenna is, the more quality and channels you will acquire.
Tip: Inspect your outdoor antenna for potential damage!
7. Restore Fetch’s TV Box to Defaults
All configurations, settings and configured content on the Fetch TV box can be restored to defaults by starting a factory reset procedure.
This solution will address issues with the channel signal decoding and the encryption of FTA channels and improve the functionality.
However, we strongly recommend performing this step only as a last resort after you have attempted all the previous solutions and nothing helped.
Here’s how to restore the Fetch TV box to factory defaults:
- Enter the Main Menu of the Fetch TV box.
- Select “Manage” and go down to “Settings.”
- Choose “Device Info” in the right-side menu.
- After that, choose “Factory Settings Reset.”
- Next, enter the default (0000) PIN to proceed.
After starting the factory reset, the Fetch TV box will be temporarily unavailable while all settings and options are restored to default values.
Do not interact with the box while it is still resetting.
To fix whenever Fetch TV troubleshooting no signal, power cycle the TV box, reconnect the antenna cable and re-tune for channels.
If the issue persists, inspect the connection with the TV and factory reset the TV box.
Follow us for more!
Finn Wheatley holds a Master’s Degree in Computer Science from UCL, London. He helped small data science consultancy firms, helping large corporations to grow their data capabilities, deploy advanced machine learning-based analytics and troubleshoot tech-related issues. Check out more about him here.